A prefabricated substation is a complete medium-to-low voltage substation — MV switchgear, distribution transformer, LV distribution board and auxiliaries — built, wired and tested inside an enclosure at a factory, then delivered to site as a single unit. Also called a packaged substation, compact substation, unit substation or, in some markets, a kiosk substation.
The argument for building it in a factory
A conventional substation is assembled on site: a civil building is constructed, equipment arrives separately over weeks, and cabling, testing and commissioning happen in the open, subject to weather, site access and the availability of specialist labour in that location.
A prefabricated unit inverts that. The work happens in controlled factory conditions with the right tools and trained staff, and the finished substation is tested as a system before it leaves. What arrives on site is a unit that needs a foundation, cable terminations and energisation.
- Site time falls from months to days. On a project where the substation is on the critical path — and it usually is — that is the whole business case.
- Quality is repeatable. Factory wiring under supervision is more consistent than field wiring in a trench in the rain.
- It is tested as a complete assembly, not as separate pieces that meet each other for the first time on site.
- Remote and difficult sites become practical. For mine sites, desert solar plant and island networks, the alternative is mobilising a full construction crew.
- Type-tested internal arc performance is verified on the enclosure design rather than argued about for a bespoke building.
What is inside
- MV compartment — commonly a ring main unit or MV switchgear panel, SF6 or solid dielectric, with switch-fuse or circuit breaker protection for the transformer
- Transformer compartment — oil-immersed or cast resin dry-type distribution transformer
- LV compartment — main LV panel, outgoing ways, metering, and often power factor correction
- Auxiliaries — lighting, ventilation, anti-condensation heating, earthing system, fire detection where required
- Enclosure — sheet steel, GRP or concrete, with the appropriate corrosion and IP class for the site
Enclosure material
Concrete
The most robust option, excellent fire performance and thermal mass, and effectively immune to vandalism. Heavy — which drives transport and lifting costs and dictates the foundation. Common in urban distribution networks.
Sheet steel
Lighter and cheaper to transport, with wide flexibility of layout. Corrosion protection is the specification that matters, particularly in coastal or industrial atmospheres.
GRP (glass reinforced plastic)
Corrosion-proof and light, well suited to coastal and chemically aggressive environments. Fire performance and mechanical robustness need to be checked against the application.
Oil or dry-type transformer
This choice is usually dictated by location rather than preference. Oil-immersed transformers are more efficient and cheaper for a given rating, but carry a fire load and generally require oil containment. Cast resin dry-type transformers eliminate the oil and are commonly mandatory for installations inside buildings, in tunnels, or above occupied spaces — at a higher cost and, typically, a larger footprint for the same rating.
What to specify
- MV system voltage and equipment rated voltage — 11, 12, 24 or 33/36 kV
- Fault level and duration at the point of connection — the parameter most often understated, and the one that cannot be corrected later
- Transformer rating and vector group
- LV configuration — number and rating of outgoing ways, metering, PFC requirement
- Internal arc classification for the enclosure, with rating and duration
- Ambient design conditions — maximum ambient temperature, altitude and solar radiation, all of which derate the transformer
- Site constraints — access route, crane capacity, foundation type and available footprint
- Standards — IEC 62271-202 governs high-voltage/low-voltage prefabricated substations
The specification error that costs most
Ambient temperature. A substation designed for a 40 °C ambient and installed where summer shade temperature reaches 50 °C, with the enclosure in full sun, will run its transformer permanently above the temperature its rating assumed. Nothing fails immediately; the transformer simply ages several times faster than the design intended.
Ventilation design, enclosure colour, solar shading and transformer derating all follow from the ambient figure. Give the real site conditions, not the standard reference values.
Browse and enquire
See current listings under Prefabricated Substations, Substation & Switchgear and Mobile Substations.
For a quotation, send the MV voltage, fault level, transformer rating, LV configuration, ambient conditions and site access constraints. Prefabricated substations are engineered to order, so a specification discussion is normally the first step rather than a catalogue selection.