A ring main unit is the compact medium-voltage switchgear assembly that sits at the heart of a distribution ring — typically two switch-disconnectors for the incoming and outgoing cables, plus a protected way for the distribution transformer. It is the reason a fault on one section of an urban network does not take out every customer on the feeder.
Why the ring topology matters
A radial feeder serves customers in a line. A fault anywhere along it disconnects everyone downstream, and they stay off until the fault is located and repaired.
A ring feeds the same customers from both ends. When a fault occurs, the faulted section is isolated by opening the switches either side of it, and supply is restored to everyone else from the other direction — often within minutes, and increasingly automatically. The RMU is the device that makes that isolation possible at each substation around the ring.
In practice most rings are operated open at one point, so they run radially but can be reconfigured. That normally-open point is what turns a repair from an all-day outage into a switching operation.
Configurations
RMUs are described by the number and type of ways:
- 2S+1T (three-way) — two switch-disconnector cable ways and one transformer way. The standard unit for a single-transformer substation.
- 3S+1T (four-way) — adds a third cable way, for a spur or a second ring connection
- 2S+2T — two transformer ways where a substation carries two transformers
- Extensible designs — modular units that can be bolted together on site as the network grows, as against fixed non-extensible tanks
The transformer way is either a switch-fuse combination (economical, and adequate for smaller transformers) or a vacuum circuit breaker with a protection relay (necessary where the transformer is large, where discrimination with upstream protection is required, or where the network is being automated).
SF6, solid dielectric or air
SF6-insulated
The long-established design. A sealed stainless steel tank filled with SF6 gas gives a very compact unit, sealed for life, unaffected by humidity, flooding or salt-laden air — which is why SF6 RMUs are standard in underground chambers and coastal installations.
The counter-argument is environmental. SF6 has a global warming potential roughly 23,500 times that of CO₂ and an atmospheric lifetime of around 3,200 years, and F-gas regulation is tightening in several markets. Any SF6 asset carries reporting and end-of-life handling obligations.
Solid dielectric
Epoxy-encapsulated vacuum switching with no insulating gas at all. Increasingly specified where regulation, corporate carbon reporting or simple future-proofing make SF6 unattractive. Generally larger than the equivalent SF6 unit and, at present, more expensive.
Air-insulated
Simplest and cheapest, but bulkier and sensitive to humidity and pollution. Suited to indoor, controlled environments rather than street-level chambers.
What to specify
- Rated voltage — commonly 11 kV, 12 kV, 24 kV or 33/36 kV. Specify the system voltage and the equipment rating separately.
- Rated normal current — typically 630 A for the ring ways
- Short-time withstand current and duration — e.g. 20 kA for 3 s. This must match the network fault level, and it is the parameter most often got wrong when a unit is bought on price.
- Internal arc classification — IAC AFL or AFLR, with the rating and duration. This is a personnel safety specification, not a preference.
- Degree of protection — and for underground chambers, whether the unit must be submersible
- Cable connection type — separable connectors and bushing interface class
- Motorisation and communications, if the ring is to be automated or remotely operated
Outdoor and pad-mounted units
Outdoor RMUs need a weatherproof enclosure, an appropriate corrosion class for the site, and consideration of solar gain and internal condensation. Anti-condensation heaters are frequently specified and just as frequently found unpowered years later — condensation inside an outdoor MV enclosure is a genuine and common cause of insulation failure.
Ring main units available on IndusGrove
Rockwill Electric covers the gas insulated range from 12 kV to 40.5 kV, indoor and outdoor:
- RMR-12/24N SF6 ring main unit — sealed tank, GB and IEC
- 12/24 kV full gas insulated RMU — every live part inside the sealed volume
- RMR-40.5 gas insulated RMU — a compact sealed unit at 40.5 kV, where air insulated is still the default
- CCV indoor RMU, 11–17.5 kV — two cable units plus a vacuum breaker feeder
- Outdoor RMU switching station — no building required, foundation and cable trench only
For networks moving away from SF6, Giantele supplies 12 kV units in both gas-free forms — air insulated, which removes the gas entirely at the cost of size, and solid insulated, which keeps close to gas-insulated dimensions with no pressure envelope to lose.
The switch units themselves — SF6-free circuit breakers, three-position load break switches and operating mechanisms for panel builders — come from Joyelectric.
Browse and enquire
See current listings under Ring Main Units (RMU), Medium Voltage Switchgear and Substation & Switchgear.
For a quotation, send the rated voltage, fault level and duration, number and type of ways, indoor or outdoor installation, and cable type. Those six figures are enough to produce a firm specification.