A three-phase power quality analyser measures what a meter cannot: not just how much energy a site consumes, but whether the supply is fit to run the equipment connected to it. Harmonics, voltage dips, flicker, unbalance and transients do not appear on an energy bill, yet they are what trips drives, overheats transformers and shortens the life of capacitor banks.
This page covers what these instruments measure, how to specify one, and the single distinction that matters most when the results have to be defended.
Class A or Class S: the distinction that decides everything
IEC 61000-4-30 defines two measurement classes, and choosing the wrong one can make an entire survey worthless.
- Class A — specified measurement methods and tight uncertainty limits. Two different Class A instruments measuring the same signal must produce the same result within defined tolerances. This is the class required for contractual measurements, grid code compliance, regulatory reporting and dispute resolution.
- Class S — relaxed methods and wider uncertainty, intended for statistical surveys and troubleshooting.
The practical consequence is blunt. If you are trying to prove to a utility that the disturbance damaging your plant originates on their network, a Class S measurement can be dismissed. If you are simply hunting a harmonic problem inside your own factory, Class S is adequate and cheaper.
Edition 3 of the standard is the current revision. An instrument certified to Class A under Edition 3 is the strongest position to measure from.
What a three-phase analyser records
- Voltage and current — true RMS on all three phases plus neutral, with the neutral current often revealing triplen harmonics that the phase readings hide
- Harmonics and interharmonics — individual orders and total harmonic distortion. Order 50 is a common limit; higher-end instruments reach order 127 and beyond, which matters where modern converters inject high-frequency content
- Voltage dips, swells and interruptions — magnitude and duration, the events that actually stop production
- Flicker (Pst and Plt) — the parameter that governs connection of arc furnaces, welders and large motors
- Unbalance — negative and zero sequence components, which cause disproportionate heating in three-phase motors
- Power and energy — active, reactive and apparent power, power factor and displacement power factor
- Transients and inrush — captured at high sampling rates on instruments that support it
How to specify one
1. Safety category is not negotiable
The CAT rating defines where the instrument may legally and safely be connected. CAT IV 600 V covers the service entrance and the origin of the installation; CAT III 1000 V covers distribution boards and fixed installations. An instrument rated CAT III 600 V must not be connected at the incoming supply of an industrial site, regardless of what its voltage range says.
2. Match the current sensors to the job
The analyser is only as good as its clamps. Rigid iron-core clamps are accurate at low current; flexible Rogowski coils handle very high currents and awkward busbar geometry but need careful positioning. Sensor range, not instrument range, is usually what limits a measurement.
3. Decide between an analyser and a logger
A power quality analyser captures events at high resolution — waveforms, transients, dip profiles. A power and energy logger is built to be installed in a switchboard and left recording for weeks at lower resolution. Investigating a fault needs the former; an energy audit or tariff verification needs the latter. Buying one when you needed the other is the most common and most expensive specification mistake in this category.
4. Check the recording period and storage
Meaningful power quality surveys run for a minimum of one full week, capturing every daily cycle and the weekend. EN 50160 assessments are based on weekly statistics. An instrument that cannot store a week of data at the required resolution cannot complete the survey.
5. Time synchronisation for multi-point studies
Measuring at two points simultaneously — to establish whether a disturbance originates upstream or downstream — requires synchronised clocks. Instruments with an internal GPS clock make that straightforward; without it, correlating two records to the millisecond is guesswork.
Where they are used
- Grid connection studies for solar, wind and battery energy storage plant, where harmonic and flicker limits at the point of common coupling are a condition of connection
- Industrial harmonic surveys on sites with large variable frequency drive populations
- Fault investigation after unexplained drive trips, contactor dropouts or nuisance breaker operation
- Transformer and cable derating studies, where harmonic loading reduces permissible capacity
- Capacitor bank and filter design and verification
- Utility dispute evidence — the Class A application
A note on diagnosing harmonics
Harmonic problems are frequently misdiagnosed because the symptom appears far from the source. A capacitor bank that keeps failing is usually not faulty — it is resonating with the supply inductance at a harmonic frequency injected by drives elsewhere on the site, and the current circulating through it is many times its rating. Replacing the capacitors repeatedly is a common and expensive response to a problem that a single week-long measurement would identify.
Measuring the problem is half the job — correcting it is the other half
A power quality analyser tells you the network has a poor power factor, a negative-sequence imbalance or harmonic distortion. Fixing it needs compensation plant. FGI WindSun static var generators cover 6 kV to 35 kV with continuous capacitive and inductive regulation, sub-5 ms response and harmonic mitigation to the 13th order:
- 6.6 kV indoor liquid-cooled SVG (STATCOM)
- 10–13.8 kV indoor SVG and 10 kV outdoor SVG
- 35 kV outdoor SVG and 33–35 kV indoor liquid-cooled SVG
- Filter capacitors for the steady-state reactive component in a hybrid FC plus SVG scheme
The reason this matters: a plain power factor capacitor bank installed on a network already carrying 5th and 7th harmonic current will amplify those harmonics and fail. The analyser survey is what tells you whether you need a detuned passive bank, an active compensator, or both.
Browse and enquire
See the current listings under Power Quality Analyzers and Energy Meters & Analyzers, or view manufacturers including AEMC Instruments and Megger.
If you are unsure which class or configuration you need, send the application, the voltage level, the maximum current and whether the results must stand up contractually — that is enough to narrow the choice to two or three instruments.